Industrial Wireless
Firetide HotPoint wireless access points deliver a modular access solution for large scale, indoor and outdoor wireless mesh networks. Modular design enables full network and software integration of the access points with a Firetide wireless mesh network while at the same time permitting independent physical placement of the hardware to provide optimal accessibility for Wi-Fi clients.
- Leading WLAN vendors hardware can be installed such as Meru, Symbol, Cisco & Firetide
- -40°C/-20°C/-10°C/ to 60°C (32°F to 122°F) note this depends on the internal hardware used or if the enclosure heater option is fitted
- 316L stainless steel
- IP66
-
- -40ºC to +60ºC Note: ambient temperature depends on whether the enclosure heater or cooler option is fitted
- 316L stainless steel construction
- IP66
- 802.11b compliant 2.4 GHz license-free, wireless data up to 11Mb/s
- Reliable data transfer in congested industrial environments - high RF power and receiver sensitivity
- Industrial ratings, -35 degC to 65 degC, humidity to 99% - designed for demanding applications
- Secure data transfer, military grade 128-bit AES encryption, plus commercial grade WEP encryption
- Firewall protection via message filtering at MAC address level
- Redundancy for critical applications, automatic changeover at Access Point
- 10/100 BaseT Ethernet, wireless data up to 76Kbits/sec
- Repeater functionality increases wireless range
- Secure Firewall protection
- Discrete channel for status I/O
- Configuration and diagnostics via web-browser
- Quad-band GSM 850/900/1800/1900
- Supports the GSM standard AT command set
- GPRS class 10 device (carrier throughput up to 54.2 Kbps)
- Embedded TCP/IP stack
- Standard SMA antenna connector
- RS-232 serial interface
- Circuit switched data up to 14.4Kbps, V.110
- Router and Serial Server functionality
- Onboard independent RS232/485 ports
- Embedded TCP/IP, UDP, ARP, PPP, HTTP
- Modbus RTU (Master) and TCP (Master/slave) and Modbus TCP-RTU conversion inherent capability
- Data routing operating modes:
Broadcast routing, point to multipoint
Master/slave routing - broadcast mode from Master but point to point from slaves reducing data traffic and charges
Modbus aware routing - router 'learns' addressing and delivers data to desired location - further reduces data traffic and charges - Onboard DI/O for alarming, control
HotPort 6000 mesh nodes provide reliable Ethernet connectivity over a high-performance, self-forming wireless mesh backbone - indoors, outdoors, or onboard moving vehicles. All HotPort nodes have multiple Ethernet ports for connecting network devices or other networks to the wireless mesh. HotPort 6000 mesh nodes provide up to 70 Mbps throughput and operate at 2.4 GHz, 4.9 GHz (U.S. public safety licensed band), or 5 GHz. Depending on the model, HotPort 6000 nodes are equipped with either single or dual radios, operating at 400 mW.
-
- Ambient temperature range -40º to 70ºC
- Note that this temperature is dependent on whether the enclosure heating or cooling option is fitted
- Optional serial and 802.3af POE interfaces
- 316L stainless steel construction
- IP66
- Licensed and license-free radio channels
- Two serial ports + one config port
- Wireless data rate up to 19.2 Kb/s
- Military-grade security encryption - 128 bit AES
- On-line diagnostics
- Hot-redundant standby
- Wireless data up to 76.8 Kb/s
- 869.4 MHz 250KHz channel-spacing, 500mW (10% duty factor), 5mW (100%)
- Typical line-of-sight distance 5km (@ 500mW)
- One serial data port - RS232 and RS485 connections provide serial data up to 115.2Kb/s
- Configuration by Hayes AT commands or Windows Configuration software
- Wireless data up to 115.2 Kb/s
- 902-928 MHz, 1W, frequency hopping spread spectrum.
- Typical line-of-sight distance 20 miles North America (4W ERP), 15 km elsewhere (1W ERP)
- Serial data up to 115.2Kb/s (RS232/RS485)
- Configuration by Hayes AT commands or Windows Configuration software.
